Echo Edger 99944200470 User Manual

x7722271404 / x772000164  
99944200470  
Power Edger Attachment  
FOR MODELS: SRM-2100SB, 2400SB, 210SB, 211SB, 225SB,  
260SB, 261SB, PAS-2100, 2400, 2601, 210, 211, 225, 225VP,  
225VPB, 230, 231, 260, 261, 265, 266, 280  
Operator’s Manual  
Users of this equipment risk injury to themselves and others if the unit is used  
improperly and/or safety precautions are not followed. ECHO provides an operator’s  
manual. It must be read and understood for proper and safe operation. Failure to do so  
could result in serious injury.  
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time  
of publication, but are subject to change without notice. Illustrations may include optional equipment and  
accessories, and may not include all standard equipment.  
X7532278708  
© 09/2013 ECHO Inc.  
 
99944200470  
INTRODUCTION  
INTRODUCTION  
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and  
on-the-job dependability. Read and understand this manual and the SAFETY MANUAL. You will find both  
easy to use and full of helpful operating tips and SAFETY messages.  
The Operator’s Manual  
Keep it in a safe place for future reference. Contains specifications and information for safety, operation,  
maintenance, storage and assembly specific to this product.  
The Safety Manual  
Keep it in a safe place for future reference. Explains possible hazards and the measures you should take to  
insure safe operation.  
SERVICING INFORMATION  
Parts/Serial Number  
Genuine ECHO Parts and ECHO REPOWER™ Parts and  
Assemblies for your ECHO products are available only from an  
Authorized ECHO Dealer. When you do need to buy parts always  
have the Model Number and Serial Number of the unit with you. You  
can find these numbers on the engine housing. For future  
reference, write them in the space provided below.  
Model No. _________________ SN. ___________________  
Service  
Service of this product during the warranty period must be performed by an Authorized ECHO Service  
Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or  
call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site. When presenting your  
unit for Warranty service/repairs, proof of purchase is required.  
Echo Consumer Product Support  
If you require assistance or have questions concerning the application, operation or maintenance of this  
product you may call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:30 am to  
4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial  
number of your unit.  
Warranty Registration  
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at  
product confirms your warranty coverage and provides a direct link between you and ECHO if we find it  
necessary to contact you.  
X7532278708  
3
© 09/2013 ECHO Inc.  
 
               
SAFETY  
99944200470  
Additional or Replacement Manuals  
Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at  
(800-673-1558). Always check the ECHO Web Site for updated information.  
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.  
SAFETY  
Refer to your Pro Attachment Series or Split Boom Operator's Manual for correct engine fueling,  
starting and stopping instructions.  
Manual Safety Symbols and Important Information  
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational  
messages preceded by symbols or key words. The following is an explanation of those symbols and key  
words and what they mean to you.  
The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition  
which WILL lead to serious personal injury or death if not avoided.  
The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition  
which CAN lead to serious personal injury or death if not avoided.  
The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition  
which may lead to minor or moderate personal injury if not avoided.  
The enclosed message provides information necessary for the protection of the unit.  
Note: This enclosed message provides tips for use, care and maintenance of the unit.  
CIRCLE AND SLASH SYMBOL  
This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result  
in serious or fatal injury.  
4
X7532278708  
© 09/2013 ECHO Inc.  
 
     
99944200470  
SAFETY  
International Symbols  
Symbol  
Description  
Symbol  
Description  
Symbol  
Description  
Symbol  
Description  
Warning, See  
Operator’s  
Manual  
DO NOT USE  
BLADES - Line  
Head Only  
Thrown  
objects  
Safety/Alert  
Wear eye, ear  
and head  
protection  
Plan retreat  
pathfromfalling  
objects  
Finger Severing  
Wear hand  
and foot  
protection  
A V O ID K IC KO UT .  
Keep bystanders at least 15 meters  
(50 feet) away.  
RotatingCutting  
Attachment  
Wear slip  
resistant foot  
wear  
Wear Face  
Shield  
Beware Thrown Objects  
Wear Eye Protection  
Do not operate  
closer than 15 M  
(50 ft.) from  
Keep feet  
away from  
blade  
electricalhazards.  
Keep  
Keep bystanders and helpers  
away 15 m (50 ft.).  
bystanders at  
le a s t 1 5 m e t e r s  
(50 feet) away  
Personal Condition and Safety Equipment  
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety  
precautions are not followed. Proper clothing and safety gear must be worn when operating unit.  
Physical Condition  
Your judgment and physical dexterity may not be good:  
• if you are tired or sick,  
• if you are taking medication,  
• if you have taken alcohol or drugs.  
Operate unit only if you are physically and mentally well.  
Eye Protection  
Eye protection that meets ANSI Z87.1, CE, or CSA Z94.3 requirements must be worn whenever you operate  
the unit.  
Hand Protection  
Wear no-slip, heavy duty work gloves to improve your grip on the handles. Gloves also reduce the  
transmission of machine vibration to your hands.  
Breathing Protection  
Wear a facemask to protect against dust.  
X7532278708  
5
© 09/2013 ECHO Inc.  
 
SAFETY  
99944200470  
Hearing Protection  
ECHO recommends wearing hearing protection whenever unit is used.  
Proper Clothing  
Wear snug fitting, durable clothing;  
• Pants should have long legs, shirts with long sleeves.  
• DO NOT WEAR SHORTS,  
• DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become  
entangled in moving parts or surrounding growth.  
Wear sturdy work shoes with nonskid soles;  
• DO NOT WEAR OPEN TOED SHOES,  
• DO NOT OPERATE UNIT BAREFOOTED.  
Wear no-slip, heavy duty work gloves.  
Keep long hair away from engine and air intake. Retain hair with cap or net.  
Hot Humid Weather  
Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work  
for early morning or late afternoon hours when temperatures are cooler.  
The ignition components of this machine generate an electromagnetic field during operation which  
may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with  
pacemakers should consult with their physician and the pacemaker manufacturer before operating  
this machine. In the absence of such information, ECHO does not recommend the use of ECHO  
products by anyone who has a pacemaker.  
Vibration and Cold  
It is believed that a condition called Raynaud’s Phenomenon,  
which affects the fingers of certain individuals, may be brought  
about by exposure to vibration and cold. Exposure to vibration  
and cold may cause tingling and burning sensations, followed  
by loss of color and numbness in the fingers. The following  
precautions are strongly recommended, because the minimum  
exposure, which might trigger the ailment, is unknown.  
• Keep your body warm, especially the head, neck, feet, ankles,  
hands, and wrists.  
• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and  
also by not smoking.  
• Limit the hours of operation. Try to fill each day with jobs where operating the unit or other hand-held  
power equipment is not required.  
• If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling,  
consult your physician before further exposing yourself to cold and vibration.  
6
X7532278708  
© 09/2013 ECHO Inc.  
 
99944200470  
SAFETY  
Repetitive Stress Injuries  
It is believed that overusing the muscles and tendons of the  
fingers, hands, arms, and shoulders may cause soreness,  
swelling, numbness, weakness, and extreme pain in those  
areas. Certain repetitive hand activities may put you at a high  
risk for developing a Repetitive Stress Injury (RSI). An extreme  
RSI condition is Carpal Tunnel Syndrome (CTS), which could  
occur when your wrist swells and squeezes a vital nerve that  
runs through the area. Some believe that prolonged exposure to  
vibration may contribute to CTS. CTS can cause severe pain for  
months or even years.  
To reduce the risk of RSI/CTS, do the following:  
• Avoid using your wrist in a bent, extended, or twisted position. Instead try to maintain a straight wrist  
position. Also, when grasping, use your whole hand, not just the thumb and index finger.  
Take periodic breaks to minimize repetition and rest your hands.  
• Reduce the speed and force with which you do the repetitive movement.  
• Do exercise to strengthen the hand and arm muscles.  
• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in  
the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve  
and muscle damage can be prevented.  
All over head electrical conductors and communications wires can have electricity flow with high  
voltages. This unit is not insulated against electrical current. Never touch wires directly or indirectly,  
otherwise serious injury or death may result.  
Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains  
poisonous emissions and can cause serious injury or death.  
Read the Manuals  
• Provide all users of this equipment with the Operator’s Manual  
and Safety Manual for instructions on Safe Operation.  
Clear the Work Area  
• Spectators and fellow workers must be warned, and children  
and animals prevented from coming nearer than 15 m (50 ft.)  
while the unit is in use.  
Keep a Firm Grip  
• Always hold throttle handle and support handle with thumbs  
and fingers tightly encircling the handles.  
Keep a Solid Stance  
• Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not  
work in odd positions or on ladders. Do not over reach.  
X7532278708  
7
© 09/2013 ECHO Inc.  
 
SAFETY  
99944200470  
Avoid Hot Surfaces  
• During operation, the drive shaft housing and attachment  
bearing housing may become very hot, too hot to touch. Avoid  
contact during and immediately after operation.  
Equipment  
Use this attachment with ECHO approved models only. Serious injury may result from the use of this  
attachment combined with a non approved ECHO product.  
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.  
• Inspect shield for damage and that shield is securely in place. Replace if sjield is damaged or missing.  
• Check that the cutting attachment is firmly attached and in safe operating condition.  
Note: ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories  
which have not been tested and approved by ECHO.  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects  
away from all openings.  
ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete  
stop before removing obstructions, clearing debris, or servicing unit.  
DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.  
NEVER reach into any opening while the engine is running. Moving parts may not be visible through  
openings.  
8
X7532278708  
© 09/2013 ECHO Inc.  
 
 
99944200470  
DESCRIPTION  
DESCRIPTION  
Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow  
the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See  
PARTS ORDERING instructions for specific information.  
3
2
4
1
Shaft Label  
1. BLADE - Rotates to provide cutting action.  
2. DEBRIS SHIELD/FLAP - Mounted over the cutting attachment. Helps protect operator by deflecting  
debris produced during the edging operation.  
3. DRIVE SHAFT ASSEMBLY - Contains a specially designed liner and the flexible drive shaft.  
4. WHEEL - Adjustable up/down, sets depth of blade.  
X7532278708  
9
© 09/2013 ECHO Inc.  
 
 
CONTENTS  
99944200470  
CONTENTS  
The ECHO product you purchased has been factory pre-assembled for your convenience.  
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or  
missing parts. Use the contents list to check for missing parts.  
____ - 1 - Power Edger Attachment  
____ 1 - Operator’s Manual  
X7722271404  
/
X772000164  
99944200475  
Power Edger  
Attachment  
____ 1 - Warranty Registration Card  
____ 2 - Split pin  
Operator’s Manual  
Burn Hazard  
The muffler or catalytic muffler and surrounding cover may become extremely hot.  
Always keep clear of exhaust and muffler area, otherwise serious personal injury may occur.  
The engine exhaust from this product contains chemicals known to the State of California to cause cancer.  
birth defects or other reproductive harm.  
____ 1 - Storage Hook Assembly  
Read rules for safe operation and instructions carefully. ECHO provides an Operators Manual  
and  
a
Safety Manual. Both must be read and understood for proper and safe operation.  
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time  
of publication, but are subject to change without notice. Illustrations may include optional equipment and  
accessories, and may not include all standard equipment.  
X7722271404 / X772000164  
©
4/2011 ECHO Inc.  
10  
X7532278708  
© 09/2013 ECHO Inc.  
 
 
99944200470  
ASSEMBLY  
ASSEMBLY  
Power Head Shaft/Lower Shaft Assembly  
Do not perform maintenance or assembly procedures with engine running.  
Parts Required:  
PAS or SRM-SB Power Head w/Shaft &  
Coupling  
1. Set Power Head/Shaft Assembly on a level surface.  
B
2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn  
to lock-out position.  
D
3. Remove vinyl cap from attachment drive shaft.  
4. Remove cardboard spacer, if necessary.  
E
C
5. Carefully fit attachment drive shaft assembly into coupler (B)  
to decal assembly line (C), making sure that the inner lower  
drive shaft engages the square upper drive shaft socket.  
A
Note: Earlier model Power Heads may have shorter couplings.  
Short couplings fit flush to decal point (E). New couplings  
are 4-3/4 in. long, and fit flush to line (C).  
Note: Lower bearing housing and head assembly must be in line with the engine.  
6. Rotate locator pin (A) 1/4 turn clockwise to engage lower  
D
shaft hole. Insure locator pin is fully engaged by twisting  
lower drive shaft. Locator pin should snap flush in coupler.  
Full engagement will prevent further shaft rotation.  
C
7. Secure lower shaft assembly to coupler by tightening  
clamping knob (D).  
X7532278708  
11  
© 09/2013 ECHO Inc.  
 
   
OPERATION  
99944200470  
OPERATION  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects  
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts  
have come to a completestop before removing obstructions, clearing debris, or servicing unit. Allow  
unit to cool before performing service.  
Operation Techniques  
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause  
unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position  
unit so that exhaust is directed away from your face and body.  
1. Before edging, water the area to soften the ground to make  
edging easier.  
2. Before edging, check the area and remove all obstacles and  
objects that could be thrown.  
3. Plan to edge regularly to make it easier to keep a neat edge  
and to avoid having to make more than one pass.  
Note: Blade depth may have to be adjusted due to differences  
in height between the hard surface and the top of the  
grass.  
Never adjust blade height with engine running, otherwise serious personal injury may result.  
4. Loosen adjustment knob and adjust the blade's depth of cut  
to produce a fine cut between sidewalk and grass using a  
minimum blade depth, usually with about 13 mm (1/2 in.) of  
the blade into the ground. Tighten adjustment knob.  
5. Before edging, plan your direction of travel so that the unit  
will always be positioned on your right side and so that you  
walk on a hard surface whenever possible.  
6. Hold edger as shown.  
Before edging, be sure to read and understand the entire  
Operator's Manual to avoid serious injury.  
12  
X7532278708  
© 09/2013 ECHO Inc.  
 
   
99944200470  
OPERATION  
7. When starting to edge, run the engine at full throttle, and  
lower the blade gently into the ground, being careful not to  
hit the concrete with the blade.  
8. Don't force the blade. Move only as quickly as the blade will  
allow.  
The complete unit, specifically the drive shaft assembly  
and muffler exhaust area may become very hot during use.  
Avoid contact during and immediately after operation,  
otherwise serious personal injury may result.  
X7532278708  
13  
© 09/2013 ECHO Inc.  
 
MAINTENANCE  
99944200470  
MAINTENANCE  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects  
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts  
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.  
Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and  
hot surfaces.  
Your ECHO unit is designed to provide many hours of trouble free service. Regular scheduled maintenance  
will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, you may  
want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to  
DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is  
not listed, see your ECHO Dealer for repairs.  
Skill Levels  
Level 1 = Easy to do. Common tools may be required.  
Level 2 = Moderate difficulty. Some specialized tools may be required.  
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.  
Maintenance Intervals  
Skill  
Level  
Component/System  
Maintenance Procedure  
Grease  
Interval  
Drive Shaft  
1
1
1
Every 25 hours of use [1]  
Every15 - 25 hours of use [1]  
Before Each Use  
Gear Housing  
Grease  
Screws/Nuts/Bolts  
Inspect/Tighten/Replace  
IMPORTANT - Time intervals shown are maximum. Actual use and your experience will determine the  
frequency of required maintenance.  
(1) Apply POWER BLENDXTM grease.  
Blade Replacement/Lubrication  
Level 1.  
POWER BLENDXTM 8 oz. or Lithium Base  
Grease, Blade, new split pin  
Parts Required:  
Gear Case  
Note: Grease gear case every 15 - 25 hours of use. Replace  
blade when it is worn shorter than 6 in. Remove blade and holders before greasing to prevent  
damage to gear and bearings.  
1. Shut engine off.  
2. Remove split pin (A).  
14  
X7532278708  
© 09/2013 ECHO Inc.  
 
       
99944200470  
MAINTENANCE  
3. Rotate blade until holes in inner blade adapter (B) and gear  
box align. Insert locking tool to lock PTO shaft (C).  
Note: Blade nut (D) is left hand thread.  
4. Remove blade nut (D) in a clockwise direction using  
T-wrench. Remove outer blade adapter (E), blade (F) and  
inner blade adapter (B).  
5. Clean all loose debris from gear box.  
6. Remove plug (G) and check level of grease. Grease should  
fill gear case to bottom of grease plug hole.  
B
C
F
E
D
A
7. Add grease if necessary using squeeze-type tube. Do not  
use high pressure grease gun. DO NOT over-fill.  
8. Install inner blade adapter (B) onto PTO shaft (C).  
9. Install and center new blade (F) onto inner adapter (B).  
G
10. Install outer adapter (E) and nut (D). Tighten nut (D) firmly,  
counterclockwise (CCW).  
Note: Never reuse old split pin.  
11. Install new split pin (A) to secure nut.  
X7532278708  
15  
© 09/2013 ECHO Inc.  
 
MAINTENANCE  
99944200470  
Drive Shaft (Lower)  
A
1. Loosen screws (A) and remove center locating screw (B).  
Pull gear box and shield from drive shaft housing.  
2. Pull flexible cable (C) from the drive shaft housing, wipe  
clean and re-coat with a thin coating [15 ml (1/2 oz.)] of  
grease.  
3. Slide the flexible cable (C) back in the drive housing. DO  
NOT get dirt on the flex cable.  
B
4. Install the gear housing and shield assembly.  
5. Tighten screws securely.  
C
16  
X7532278708  
© 09/2013 ECHO Inc.  
 
 
99944200470  
STORAGE  
STORAGE  
Storage Hook Installation  
1. Insert small end of hook into locating hole on attachment  
shaft.  
2. Slide plastic cap onto end of attachment shaft.  
X7532278708  
17  
© 09/2013 ECHO Inc.  
 
   
SPECIFICATIONS  
99944200470  
SPECIFICATIONS  
MODEL  
Shaft Length  
99944200470  
845 mm (33.25 in.)  
Attachment Width  
Attachment Height  
Weight w/blade  
Drive Shaft Type  
Rotating Direction  
Blade Length  
165.1 mm (6.50 in.)  
552.45 mm (21.75 in.)  
2.54 kg (5.6 lb.)  
6.35 mm (1/4 in.) Flex Shaft  
Clockwise; viewed from right side  
203 mm (8 in.)  
Gear Case Ratio  
Shield  
2.07 : 1.0 Reduction  
Open, anti-clog  
18  
X7532278708  
© 09/2013 ECHO Inc.  
 
 
99944200470  
WARRANTY STATEMENTS  
WARRANTY STATEMENTS  
ECHO LIMITED WARRANTY STATEMENT FOR  
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010  
ECHO'S RESPONSIBILITY  
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.  
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product  
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED  
WARRANTY IS ONLYAPPLICABLE TO ECHO PRODUCTS SOLD BYAUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL  
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair  
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any  
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty  
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.  
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers  
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.  
OWNER’S RESPONSIBILITY  
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COMꢀꢁꢂꢀꢃꢄꢀꢅꢆꢆ-  
ꢇꢈꢉꢀꢁꢊꢋꢀꢋꢌꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢂꢍꢉꢇꢐꢋꢂꢏꢋꢇꢁꢈꢀꢑꢏꢂꢒꢀꢐꢊꢓꢓꢆꢇꢍꢒꢀꢎꢇꢋꢌꢀꢄꢁꢊꢂꢀꢊꢈꢇꢋꢔꢀꢕꢍꢉꢇꢐꢋꢍꢂꢇꢈꢉꢀꢄꢁꢊꢂꢀꢓꢂꢁꢒꢊꢑꢋꢀꢑꢁꢈꢅꢂꢖꢐꢀꢄꢁꢊꢂꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢑꢁꢗꢍꢂꢏꢉꢍꢀꢏꢈꢒꢀꢓꢂꢁꢗꢇꢒꢍꢐꢀꢏꢀꢒꢇꢂꢍꢑꢋꢀ  
ꢆꢇꢈꢘꢀꢇꢙꢀꢎꢍꢀꢅꢈꢒꢀꢇꢋꢀꢈꢍꢑꢍꢐꢐꢏꢂꢄꢀꢋꢁꢀꢑꢁꢈꢋꢏꢑꢋꢀꢄꢁꢊꢔ  
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the  
ꢁꢓꢍꢂꢏꢋꢁꢂꢝꢐꢀꢖꢏꢈꢊꢏꢆꢔꢀꢚꢌꢁꢊꢆꢒꢀꢏꢀꢓꢂꢁꢒꢊꢑꢋꢀꢒꢇꢙꢅꢑꢊꢆꢋꢄꢀꢁꢑꢑꢊꢂꢛꢀꢄꢁꢊꢀꢖꢊꢐꢋꢛꢀꢏꢋꢀꢄꢁꢊꢂꢀꢍꢜꢓꢍꢈꢐꢍꢛꢀꢒꢍꢆꢇꢗꢍꢂꢀꢁꢂꢀꢐꢌꢇꢓꢀꢄꢁꢊꢂꢀ!"#$ꢀꢊꢈꢇꢋꢀꢋꢁꢀꢏꢈꢀꢏꢊꢋꢌꢁꢂꢇ%ꢍꢒꢀ!"#$ꢀꢐꢍꢂꢗꢇꢑꢇꢈꢉꢀ  
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been  
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO  
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you  
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.  
PRODUCT WARRANTY PERIOD  
RESIDENTIAL APPLICATION  
#ꢀꢀ 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for [ꢀꢁ ꢂꢃꢄꢅꢆꢁꢇꢈꢉ from  
date of purchase.  
EXCEPTIONS:  
#ꢀ 'ꢁꢂꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢍꢈꢉꢇꢈꢍꢀꢓꢁꢎꢍꢂꢍꢒꢀꢓꢂꢁꢒꢊꢑꢋꢐꢛꢀꢋꢌꢍꢀꢍꢆꢍꢑꢋꢂꢁꢈꢇꢑꢀꢇꢉꢈꢇꢋꢇꢁꢈꢀꢖꢁꢒꢊꢆꢍꢛꢀ\ꢍꢜꢇꢃꢆꢍꢀꢒꢂꢇꢗꢍꢀꢑꢏꢃꢆꢍꢐꢛꢀꢚꢕ/ꢀꢐꢁꢆꢇꢒꢀꢒꢂꢇꢗꢍꢀꢐꢌꢏꢙꢋꢐꢛꢀꢏꢈꢒꢀ9"ꢀꢋꢇꢈꢍꢐꢀ  
are warranted for the ꢊꢋꢌꢁꢍ of the product on parts only.  
#ꢀ "ꢊꢋꢋꢇꢈꢉꢀꢏꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢀꢐꢊꢑꢌꢀꢏꢐꢛꢀꢃꢊꢋꢀꢈꢁꢋꢀꢆꢇꢖꢇꢋꢍꢒꢀꢋꢁꢛꢀꢃꢏꢂꢐꢛꢀꢑꢌꢏꢇꢈꢐꢛꢀꢐꢓꢂꢁꢑꢘꢍꢋꢐꢛꢀꢃꢆꢏꢒꢍꢐꢛꢀꢏꢈꢒꢀꢈꢄꢆꢁꢈꢀꢋꢂꢇꢖꢖꢍꢂꢀꢌꢍꢏꢒꢐꢀꢙꢁꢂꢀꢂꢍꢐꢇꢒꢍꢈꢋꢇꢏꢆꢀꢁꢂꢀꢈꢁꢈ*ꢇꢈꢑꢁꢖꢍꢀ  
producing use will be covered for failures due to defects in material or workmanship for a period of ꢎꢏꢅꢐꢇꢆꢉ from original product  
purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.  
#ꢀꢀ !"#$ꢝꢐꢀꢕꢏꢓꢇꢒꢀ:ꢁꢏꢒꢍꢂꢀꢚꢋꢂꢇꢈꢉꢀ#ꢍꢏꢒꢀꢑꢏꢂꢂꢇꢍꢐꢀꢏꢀꢆꢇꢙꢍꢋꢇꢖꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢁꢈꢀꢋꢌꢍꢀꢆꢇꢈꢍꢀꢆꢁꢑꢘꢇꢈꢉꢀꢐꢄꢐꢋꢍꢖꢛꢀꢓꢏꢂꢋꢐꢀꢁꢈꢆꢄ;ꢀꢈꢁꢀꢆꢏꢃꢁꢂꢔꢀꢕꢍꢙꢍꢂꢀꢋꢁꢀꢄꢁꢊꢂꢀꢁꢓꢍꢂꢏꢋꢁꢂꢝꢐꢀ  
manual for string head installation and maintenance instructions.  
#ꢀꢀ <ꢆꢆ=*ꢚꢍꢂꢇꢍꢐꢈꢒ>ꢕ$ꢀ<99<"#/!?9!ꢕ@!ꢚꢓꢆꢇꢋꢌꢏꢙꢋꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢏꢂꢂꢄꢌꢍꢏꢖꢍꢏꢂꢂꢏꢈꢋꢄꢊꢂꢏꢋꢇꢁꢈꢌꢍꢈꢇꢋꢐꢌꢍꢄꢂꢍꢀ  
ꢒꢍꢐꢇꢉꢈꢍꢒꢀꢋꢁꢀꢅꢋꢔ  
COMMERCIAL APPLICATION  
#ꢀꢀ 1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income  
producing use will be covered by this limited warranty for one ꢂꢑꢄꢅꢆꢁꢇꢈ from the date of purchase.  
#ꢀꢀ 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this  
limited warranty for two ꢂꢒꢄꢅꢆꢁꢇꢈꢉ from the date of purchase.  
EXCEPTIONS:  
#ꢀ 'ꢁꢂꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢍꢈꢉꢇꢈꢍꢀꢓꢁꢎꢍꢂꢍꢒꢀꢓꢂꢁꢒꢊꢑꢋꢐꢛꢀꢋꢌꢍꢀꢍꢆꢍꢑꢋꢂꢁꢈꢇꢑꢀꢇꢉꢈꢇꢋꢇꢁꢈꢀꢖꢁꢒꢊꢆꢍꢛꢀ\ꢍꢜꢇꢃꢆꢍꢀꢒꢂꢇꢗꢍꢀꢑꢏꢃꢆꢍꢐꢛꢀꢚꢕ/ꢀꢐꢁꢆꢇꢒꢀꢒꢂꢇꢗꢍꢀꢐꢌꢏꢙꢋꢐꢀꢏꢈꢒꢀ9"ꢀꢋꢇꢈꢍꢐꢛꢀ  
are warranted for the ꢊꢋꢌꢁꢍ of the product on parts only.  
#ꢀ "ꢊꢋꢋꢇꢈꢉꢀꢏꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢀꢐꢊꢑꢌꢀꢏꢐꢛꢀꢃꢊꢋꢀꢈꢁꢋꢀꢆꢇꢖꢇꢋꢍꢒꢀꢋꢁꢛꢀꢃꢏꢂꢐꢛꢀꢑꢌꢏꢇꢈꢐꢛꢀꢐꢓꢂꢁꢑꢘꢍꢋꢐꢛꢀꢃꢆꢏꢒꢍꢐꢛꢀꢏꢈꢒꢀꢈꢄꢆꢁꢈꢀꢋꢂꢇꢖꢖꢍꢂꢀꢌꢍꢏꢒꢐꢀꢙꢁꢂꢀꢑꢁꢖꢖꢍꢂꢑꢇꢏꢆꢛꢀꢇꢈꢐꢋꢇꢋꢊꢋꢇꢁꢈꢏꢆꢛꢀ  
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period  
of ꢓꢏꢅꢐꢇꢆꢉ from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by  
this warranty.  
#ꢀꢀ !"#$ꢝꢐꢀꢕꢏꢓꢇꢒꢀ:ꢁꢏꢒꢍꢂꢀꢚꢋꢂꢇꢈꢉꢀ#ꢍꢏꢒꢀꢑꢏꢂꢂꢇꢍꢐꢀꢏꢀꢆꢇꢙꢍꢋꢇꢖꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢁꢈꢀꢋꢌꢍꢀꢆꢇꢈꢍꢀꢆꢁꢑꢘꢇꢈꢉꢀꢐꢄꢐꢋꢍꢖꢛꢀꢓꢏꢂꢋꢐꢀꢁꢈꢆꢄ;ꢀꢈꢁꢀꢆꢏꢃꢁꢂꢔꢀꢕꢍꢙꢍꢂꢀꢋꢁꢀꢄꢁꢊꢂꢀꢁꢓꢍꢂꢏꢋꢁꢂꢝꢐꢀ  
manual for string head installation and maintenance instructions.  
#ꢀꢀ <ꢆꢆ=*ꢚꢍꢂꢇꢍꢐꢈꢒ>ꢕ$ꢀ<99<"#/!?9!ꢕ@!ꢚꢓꢆꢇꢋꢌꢏꢙꢋꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢏꢂꢂꢄꢌꢍꢏꢖꢍꢏꢂꢂꢏꢈꢋꢄꢊꢂꢏꢋꢇꢁꢈꢌꢍꢈꢇꢋꢐꢌꢍꢄꢂꢍꢀ  
ꢒꢍꢐꢇꢉꢈꢍꢒꢀꢋꢁꢀꢅꢋꢔ  
RENTAL APPLICATION - 90 DAYS WARRANTY  
#ꢀꢀBꢈꢇꢋꢐꢀꢙꢁꢂꢀꢂꢍꢈꢋꢏꢆꢀꢊꢐꢍꢀꢎꢇꢆꢆꢀꢃꢍꢀꢑꢁꢗꢍꢂꢍꢒꢀꢏꢉꢏꢇꢈꢐꢋꢀꢒꢍꢙꢍꢑꢋꢐꢀꢇꢈꢀꢖꢏꢋꢍꢂꢇꢏꢆꢀꢏꢈꢒꢀꢎꢁꢂꢘꢖꢏꢈꢐꢌꢇꢓꢀꢙꢁꢂꢀꢏꢀꢓꢍꢂꢇꢁꢒꢀꢁꢙꢀGJꢀꢒꢏꢄꢐꢀꢙꢂꢁꢖꢀꢋꢌꢍꢀꢒꢏꢋꢍꢀꢁꢙꢀꢓꢊꢂꢑꢌꢏꢐꢍꢔꢀ  
ꢀꢀ !"#$ꢝꢐꢀꢆꢇꢏꢃꢇꢆꢇꢋꢄꢀꢊꢈꢒꢍꢂꢀꢋꢌꢍꢀO:ꢇꢙꢍꢋꢇꢖꢍPꢀꢑꢁꢗꢍꢂꢏꢉꢍꢀꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢋꢁꢀꢙꢊꢂꢈꢇꢐꢌꢇꢈꢉꢀꢓꢏꢂꢋꢐꢀꢐꢓꢍꢑꢇꢅꢍꢒꢀꢊꢈꢒꢍꢂꢀꢋꢌꢍꢀ>ꢕ$XB"9ꢀY<ꢕꢕ<?9Zꢀ>!ꢕ@$X section of  
this warranty statement for OꢔꢋꢌꢁPꢀꢙꢂꢍꢍꢀꢁꢙꢀꢑꢌꢏꢂꢉꢍꢀꢙꢁꢂꢀꢏꢀꢓꢍꢂꢇꢁꢒꢀꢁꢙꢀꢋꢍꢈꢀ[\J]ꢀꢄꢍꢏꢂꢐꢀꢏꢙꢋꢍꢂꢀꢋꢌꢍꢀꢒꢏꢋꢍꢀꢁꢙꢀꢋꢌꢍꢀꢑꢁꢖꢓꢆꢍꢋꢍꢀꢊꢈꢇꢋꢝꢐꢀꢅꢈꢏꢆꢀꢓꢂꢁꢒꢊꢑꢋꢇꢁꢈꢔꢀ  
X7532278708  
19  
© 09/2013 ECHO Inc.  
 
 
WARRANTY STATEMENTS  
99944200470  
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES  
#ꢀꢀGJ*ꢒꢏꢄꢀꢂꢍꢐꢇꢒꢍꢈꢋꢇꢏꢆꢛꢀꢁꢂꢀꢈꢁꢈ*ꢇꢈꢑꢁꢖꢍꢀꢓꢂꢁꢒꢊꢑꢇꢈꢉꢀꢎꢏꢂꢂꢏꢈꢋꢄ  
#ꢀꢀ^J*ꢒꢏꢄꢀꢑꢁꢖꢖꢍꢂꢑꢇꢏꢆꢛꢀꢇꢈꢐꢋꢇꢋꢊꢋꢇꢁꢈꢏꢆꢛꢀꢏꢉꢂꢇꢑꢊꢆꢋꢊꢂꢏꢆꢛꢀꢇꢈꢒꢊꢐꢋꢂꢇꢏꢆꢛꢀꢇꢈꢑꢁꢖꢍꢀꢓꢂꢁꢒꢊꢑꢇꢈꢉꢛꢀꢁꢂꢀꢂꢍꢈꢋꢏꢆꢀꢏꢓꢓꢆꢇꢑꢏꢋꢇꢁꢈꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢀ  
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS  
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior  
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD  
13738 and JASO M345FD Standards. ꢕꢖꢗꢘꢅꢙꢚ!ꢁꢈꢅ"ꢊꢁ#ꢐ(ꢅ%!ꢚ&()ꢈꢚ*ꢁꢅꢘꢋꢊ ꢇꢐꢀꢏꢀꢓꢂꢍꢖꢇꢊꢖꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢁꢇꢆꢀꢐꢓꢍꢑꢇꢅꢑꢏꢆꢆꢄꢀꢙꢁꢂꢖꢊꢆꢏꢋꢍꢒꢀꢋꢁꢀꢖꢍꢍꢋꢀ@ꢚ$*  
L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors  
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.  
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:  
#ꢀ  
:ꢏꢑꢘꢀꢁꢙꢀꢆꢊꢃꢂꢇꢑꢏꢋꢇꢁꢈꢀꢁꢂꢀꢍꢈꢉꢇꢈꢍꢀꢙꢏꢇꢆꢊꢂꢍꢛꢀꢒꢊꢍꢀꢋꢁꢀꢋꢌꢍꢀꢊꢐꢍꢀꢁꢙꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢁꢇꢆꢐꢀthat do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD  
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered  
oil, will void the two-stroke engine limited warranty. !"#$>ꢁꢎꢍꢂ=ꢆꢍꢈꢒ(9ꢎꢁ*ꢚꢋꢂꢁꢘꢍ$ꢇꢆ meets the ISO-L-EGD and JASO M345FD  
Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per  
the statement listed in the EPA or California Emission Defect Warranty Explanation.  
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢊꢐꢍꢀꢁꢙꢀꢉꢏꢐꢁꢌꢁꢆꢛꢀꢑꢁꢈꢋꢏꢇꢈꢇꢈꢉꢀꢖꢍꢋꢌꢏꢈꢁꢆꢀ[ꢎꢁꢁꢒꢀꢏꢆꢑꢁꢌꢁꢆ]ꢛꢀꢁꢂꢀꢉꢏꢐꢁꢆꢇꢈꢍꢀꢑꢁꢈꢋꢏꢇꢈꢇꢈꢉꢀꢆꢍꢐꢐꢀꢋꢌꢏꢈꢀ|Gꢀꢁꢑꢋꢏꢈꢍ. Only use gasoline which  
contains |Gꢀꢁꢑꢋꢏꢈꢍꢀꢁꢂꢀꢌꢇꢉꢌꢍꢂ. Gasohol which contains a +ꢇ6ꢋ+7+\J}ꢀꢍꢋꢌꢏꢈꢁꢆꢀ[ꢉꢂꢏꢇꢈꢀꢏꢆꢑꢁꢌꢁꢆ]ꢀꢁꢂꢀ\~}ꢀ/9=!ꢀ[ꢖꢍꢋꢌꢄꢆꢋꢍꢂꢋꢇꢏꢂꢄꢃꢊꢋꢄꢆꢍꢋꢌꢍꢂ]ꢀ  
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.  
!ꢈꢉꢇꢈꢍꢀꢒꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢊꢐꢍꢀꢁꢙꢀꢍꢋꢌꢍꢂꢀꢁꢂꢀꢏꢈꢄꢀꢐꢋꢏꢂꢋꢇꢈꢉꢀ\ꢊꢇꢒꢐꢔꢀꢀ  
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢋꢏꢖꢓꢍꢂꢇꢈꢉꢀꢎꢇꢋꢌꢀꢍꢈꢉꢇꢈꢍꢀꢐꢓꢍꢍꢒꢀꢉꢁꢗꢍꢂꢈꢁꢂꢀꢁꢂꢀꢍꢖꢇꢐꢐꢇꢁꢈꢀꢑꢁꢖꢓꢁꢈꢍꢈꢋꢐꢛꢀꢁꢂꢀꢂꢊꢈꢈꢇꢈꢉꢀꢍꢈꢉꢇꢈꢍꢐꢀꢏꢃꢁꢗꢍꢀꢐꢓꢍꢑꢇꢅꢍꢒꢀꢏꢈꢒꢀꢂꢍꢑꢁꢖꢖꢍꢈꢒꢍꢒꢀ  
engine speeds as listed in your operator’s manual.  
#ꢀ  
#ꢀ  
#ꢀ  
#ꢀ  
#ꢀ  
#ꢀ  
$ꢓꢍꢂꢏꢋꢇꢁꢈꢀꢁꢙꢀꢋꢌꢍꢀꢊꢈꢇꢋꢀꢎꢇꢋꢌꢀꢇꢖꢓꢂꢁꢓꢍꢂꢆꢄꢀꢖꢏꢇꢈꢋꢏꢇꢈꢍꢒꢂꢍꢖꢁꢗꢍꢒꢀꢑꢊꢋꢋꢇꢈꢉꢀꢐꢌꢇꢍꢆꢒꢀꢁꢂꢀꢂꢍꢖꢁꢗꢍꢒꢒꢏꢖꢏꢉꢍꢒꢀꢏꢇꢂꢀꢅꢆꢋꢍꢂꢔꢀꢀ  
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢒꢇꢂꢋꢛꢀꢓꢂꢍꢐꢐꢊꢂꢍꢀꢁꢂꢀꢐꢋꢍꢏꢖꢀꢑꢆꢍꢏꢈꢇꢈꢉꢀꢋꢌꢍꢀꢊꢈꢇꢋꢛꢀꢐꢏꢆꢋꢀꢎꢏꢋꢍꢂꢛꢀꢑꢁꢂꢂꢁꢐꢇꢁꢈꢛꢀꢂꢊꢐꢋꢛꢀꢗꢏꢂꢈꢇꢐꢌꢛꢀꢏꢃꢂꢏꢐꢇꢗꢍꢐꢛꢀꢏꢈꢒꢀꢖꢁꢇꢐꢋꢊꢂꢍꢔ  
Xꢍꢙꢍꢑꢋꢐꢛꢀꢖꢏꢆꢙꢊꢈꢑꢋꢇꢁꢈꢐꢀꢁꢂꢀꢙꢏꢇꢆꢊꢂꢍꢐꢀꢂꢍꢐꢊꢆꢋꢇꢈꢉꢀꢙꢂꢁꢖꢀꢏꢃꢊꢐꢍꢛꢀꢖꢇꢐꢊꢐꢍꢛꢀꢈꢍꢉꢆꢍꢑꢋꢛꢀꢖꢁꢒꢇꢅꢑꢏꢋꢇꢁꢈꢐꢛꢀꢏꢆꢋꢍꢂꢏꢋꢇꢁꢈꢐꢛꢀꢈꢁꢂꢖꢏꢆꢀꢎꢍꢏꢂꢛꢀꢇꢖꢓꢂꢁꢓꢍꢂꢀꢐꢍꢂꢗꢇꢑꢇꢈꢉꢛꢀꢁꢂꢀꢊꢐꢍꢀ  
of unauthorized attachments.  
#ꢀ  
#ꢀ  
@ꢈꢑꢁꢂꢂꢍꢑꢋꢀꢐꢋꢁꢂꢏꢉꢍꢀꢓꢂꢁꢑꢍꢒꢊꢂꢍꢐꢛꢀꢐꢋꢏꢆꢍꢀꢙꢊꢍꢆꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢙꢏꢇꢆꢊꢂꢍꢀꢋꢁꢀꢓꢂꢁꢗꢇꢒꢍꢀꢁꢂꢀꢓꢍꢂꢙꢁꢂꢖꢀꢂꢍ€ꢊꢇꢂꢍꢒꢀꢖꢏꢇꢈꢋꢍꢈꢏꢈꢑꢍꢀꢐꢍꢂꢗꢇꢑꢍꢐꢀꢏꢐꢀꢓꢂꢍꢐꢑꢂꢇꢃꢍꢒꢀꢇꢈꢀꢋꢌꢍꢀꢁꢓꢍꢂꢏꢋꢁꢂꢐꢀ  
manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.  
'ꢏꢇꢆꢊꢂꢍꢐꢀꢒꢊꢍꢀꢋꢁꢀꢇꢖꢓꢂꢁꢓꢍꢂꢀꢐꢍꢋ*ꢊꢓꢛꢀꢓꢂꢍ*ꢒꢍꢆꢇꢗꢍꢂꢄꢀꢐꢍꢂꢗꢇꢑꢍꢀꢁꢂꢀꢂꢍꢓꢏꢇꢂꢀꢐꢍꢂꢗꢇꢑꢍꢀꢃꢄꢀꢏꢈꢄꢁꢈꢍꢀꢁꢋꢌꢍꢂꢀꢋꢌꢏꢈꢀꢏꢊꢋꢌꢁꢂꢇ%ꢍꢒꢀ!"#$ꢀꢐꢍꢂꢗꢇꢑꢇꢈꢉꢀꢒꢍꢏꢆꢍꢂꢀꢒꢊꢂꢇꢈꢉꢀꢋꢌꢍꢀ  
warranty period.  
"ꢍꢂꢋꢏꢇꢈꢀparts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.  
Bꢐꢍꢓꢏꢂꢘꢆꢊꢉꢐꢋꢌꢍꢂꢌꢏꢈꢌꢁꢐꢍꢍꢍꢋꢇꢈꢉꢍꢂꢙꢁꢂꢖꢏꢈꢑꢍꢈꢒꢊꢂꢏꢃꢇꢆꢇꢋꢄꢍ€ꢊꢇꢂꢍꢖꢍꢈꢋꢐꢌꢍ$!/ꢓꢏꢂꢘꢆꢊꢉꢇꢐꢋꢍꢒꢌꢍ$ꢓꢍꢂꢏꢋꢁꢂꢐꢀ  
Manuals.  
$ꢗꢍꢂꢌꢍꢏꢋꢇꢈꢉꢀꢁꢂꢀꢑꢏꢂꢃꢁꢈꢀꢐꢑꢁꢂꢇꢈꢉꢀꢙꢏꢇꢆꢊꢂꢍꢐꢀꢒꢊꢍꢀꢋꢁꢀꢂꢍꢐꢋꢂꢇꢑꢋꢍꢒꢛꢀꢑꢆꢁꢉꢉꢍꢒꢀꢍꢜꢌꢏꢊꢐꢋꢀꢓꢁꢂꢋꢀꢁꢂꢀꢑꢁꢖꢃꢊꢐꢋꢇꢁꢈꢀꢑꢌꢏꢖꢃꢍꢂꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢒꢏꢖꢏꢉꢍꢀꢋꢁꢀꢐꢓꢏꢂꢘꢀꢏꢂꢂꢍꢐꢋꢍꢂꢀ  
screen.  
#ꢀ  
#ꢀ  
#ꢀ  
#ꢀ  
#ꢀ  
<ꢒƒꢊꢐꢋꢖꢍꢈꢋꢐꢀꢏꢙꢋꢍꢂꢀꢋꢌꢍꢀꢅꢂꢐꢋꢀ[^J]ꢀꢋꢌꢇꢂꢋꢄꢀꢒꢏꢄꢐꢀꢏꢈꢒꢀꢃꢍꢄꢁꢈꢒꢛꢀꢐꢊꢑꢌꢀꢏꢐꢀꢑꢏꢂꢃꢊꢂꢍꢋꢁꢂꢀꢏꢒƒꢊꢐꢋꢖꢍꢈꢋꢀꢏꢈꢒꢀꢋꢌꢂꢁꢋꢋꢆꢍꢀꢑꢏꢃꢆꢍꢀꢏꢒƒꢊꢐꢋꢖꢍꢈꢋꢔꢀ  
Xꢏꢖꢏꢉꢍꢀꢋꢁꢀꢉꢍꢏꢂꢐꢀꢁꢂꢀꢉꢍꢏꢂꢀꢑꢏꢐꢍꢐꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢑꢁꢈꢋꢏꢖꢇꢈꢏꢋꢍꢒꢀꢉꢂꢍꢏꢐꢍꢀꢁꢂꢀꢁꢇꢆꢛꢀꢊꢐꢍꢀꢁꢙꢀꢇꢈꢑꢁꢂꢂꢍꢑꢋꢀꢋꢄꢓꢍꢀꢁꢂꢀꢗꢇꢐꢑꢁꢐꢇꢋꢄꢀꢁꢙꢀꢆꢊꢃꢂꢇꢑꢏꢈꢋꢐꢛꢀꢏꢈꢒꢁꢂꢀꢙꢏꢇꢆꢊꢂꢍꢀꢋꢁꢀꢑꢁꢖꢓꢆꢄꢀ  
with recommended grease or oil change intervals.  
#ꢀ  
#ꢀ  
#ꢀ  
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢆꢁꢏꢒꢇꢈꢉꢀꢚ#ꢕ!Xꢀ?ꢀ„<"® beyond recommended capacity.  
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢓꢊꢖꢓꢀꢁꢂꢀꢐꢓꢂꢏꢄꢍꢂꢀꢂꢊꢈꢈꢇꢈꢉꢀꢒꢂꢄꢛꢀꢓꢊꢖꢓꢇꢈꢉꢀꢁꢂꢀꢐꢓꢂꢏꢄꢇꢈꢉꢀꢑꢏꢊꢐꢋꢇꢑꢀꢁꢂꢀ\ꢏꢖꢖꢏꢃꢆꢍꢀꢖꢏꢋꢍꢂꢇꢏꢆꢐꢛꢀꢁꢂꢀꢆꢏꢑꢘꢀꢁꢙꢀꢁꢂꢀꢃꢂꢁꢘꢍꢈꢀꢐꢋꢂꢏꢇꢈꢍꢂꢐꢔꢀ  
<ꢒꢒꢇꢋꢇꢁꢈꢏꢆꢀꢒꢏꢖꢏꢉꢍꢀꢋꢁꢀꢓꢏꢂꢋꢐꢀꢁꢂꢀꢑꢁꢖꢓꢁꢈꢍꢈꢋꢐꢀꢒꢊꢍꢀꢋꢁꢀꢑꢁꢈꢋꢇꢈꢊꢍꢒꢀꢊꢐꢍꢀꢏꢙꢋꢍꢂꢀꢁꢓꢍꢂꢏꢋꢇꢁꢈꢏꢆꢀꢓꢂꢁꢃꢆꢍꢖꢀꢁꢂꢀꢙꢏꢇꢆꢊꢂꢍꢀꢁꢑꢑꢊꢂꢐꢔꢀꢚꢌꢁꢊꢆꢒꢀꢁꢓꢍꢂꢏꢋꢇꢁꢈꢏꢆꢀꢓꢂꢁꢃꢆꢍꢖꢀꢁꢂꢀ  
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.  
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting  
WWW.ECHO-USA.COMꢔꢀZꢁꢊꢂꢀꢂꢍꢑꢍꢇꢓꢋꢀꢁꢙꢀꢓꢊꢂꢑꢌꢏꢐꢍꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢒꢏꢋꢍꢛꢀꢖꢁꢒꢍꢆꢀꢏꢈꢒꢀꢐꢍꢂꢇꢏꢆꢀꢈꢊꢖꢃꢍꢂꢀꢖꢊꢐꢋꢀꢃꢍꢀꢖꢏꢇꢈꢋꢏꢇꢈꢍꢒꢀꢏꢈꢒꢀꢓꢂꢍꢐꢍꢈꢋꢍꢒꢀꢋꢁꢀꢏꢈꢀꢏꢊꢋꢌꢁꢂꢇ%ꢍꢒꢀ  
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long  
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or  
ꢑꢁꢈꢐꢍ€ꢊꢍꢈꢋꢇꢏꢆꢀꢒꢏꢖꢏꢉꢍꢐꢛꢀꢐꢁꢀꢄꢁꢊꢀꢖꢏꢄꢀꢏꢆꢐꢁꢀꢌꢏꢗꢍꢀꢁꢋꢌꢍꢂꢀꢐꢓꢍꢑꢇꢅꢑꢀꢆꢍꢉꢏꢆꢀꢂꢇꢉꢌꢋꢐꢀꢎꢌꢇꢑꢌꢀꢗꢏꢂꢄꢀꢙꢂꢁꢖꢀꢐꢋꢏꢋꢍꢀꢋꢁꢀꢐꢋꢏꢋꢍꢔꢀ9ꢌꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢇꢐꢀꢉꢇꢗꢍꢈꢀꢃꢄꢀ!"#$ꢀ  
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.  
DISCLAIMER OF IMPLIED WARRANTIES  
9ꢌꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢇꢐꢀꢇꢈꢀꢆꢇꢍꢊꢀꢁꢙꢀꢏꢆꢆꢀꢁꢋꢌꢍꢂꢀꢍꢜꢓꢂꢍꢐꢐꢍꢒꢀꢁꢂꢀꢇꢖꢓꢆꢇꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢇꢍꢐꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢏꢈꢄꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢁꢙꢀ'@9?!ꢚꢚꢀ'$ꢕꢀ<ꢀ><ꢕ9@"B:<ꢕꢀ>Bꢕ>$ꢚ!ꢀ  
OR USE and any implied warranty of MERCHANTABILITYꢀꢁꢋꢌꢍꢂꢎꢇꢐꢍꢀꢏꢓꢓꢆꢇꢑꢏꢃꢆꢍꢀꢋꢁꢀꢋꢌꢇꢐꢀꢓꢂꢁꢒꢊꢑꢋꢔꢀ!"#$ꢀꢏꢈꢒꢀꢇꢋꢐꢀꢏꢙꢅꢆꢇꢏꢋꢍꢒꢀꢑꢁꢖꢓꢏꢈꢇꢍꢐꢀꢐꢌꢏꢆꢆꢀꢈꢁꢋꢀꢃꢍꢀ  
ꢆꢇꢏꢃꢆꢍꢀꢙꢁꢂꢀꢏꢈꢄꢀꢐꢓꢍꢑꢇꢏꢆꢀꢇꢈꢑꢇꢒꢍꢈꢋꢏꢆꢀꢁꢂꢀꢑꢁꢈꢐꢍ€ꢊꢍꢈꢋꢇꢏꢆꢀꢒꢏꢖꢏꢉꢍꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢆꢁꢐꢋꢀꢓꢂꢁꢅꢋꢐꢔꢀ9ꢌꢍꢂꢍꢀꢏꢂꢍꢀꢈꢁꢀꢎꢏꢂꢂꢏꢈꢋꢇꢍꢐꢀꢍꢜꢋꢍꢈꢒꢍꢒꢀꢁꢋꢌꢍꢂꢀꢋꢌꢏꢈꢀꢏꢐꢀꢓꢂꢁꢗꢇꢒꢍꢒꢀꢌꢍꢂꢍꢇꢈꢔꢀ  
9ꢌꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢖꢏꢄꢀꢃꢍꢀꢖꢁꢒꢇꢅꢍꢒꢀꢁꢈꢆꢄꢀꢃꢄꢀ!"#$ꢔ  
99922201032  
11/18/2011  
20  
X7532278708  
© 09/2013 ECHO Inc.  
 
99944200470  
NOTES  
NOTES  
X7532278708  
21  
© 09/2013 ECHO Inc.  
 
 
NOTES  
99944200470  
22  
X7532278708  
© 09/2013 ECHO Inc.  
 
99944200470  
NOTES  
X7532278708  
23  
© 09/2013 ECHO Inc.  
 
ECHO, INCORPORATED  
400 Oakwood Road  
S06000057001/S06000999999  
Lake Zurich, IL 60047  
www.echo-usa.com  
24  
 

Extron electronic Switch TPX 88 User Manual
Fisher Price Car Seat EF20B User Manual
Flymo Trimmer Contour Power Plus Cordless Trimmer User Manual
Frigidaire Kitchen Grill Grill with Electronic Ignition User Manual
FujiFilm Camcorder 16109884 User Manual
GBC Paper Shredder GDHS7 User Manual
GE Computer Monitor EPM 5200 User Manual
GE Trash Compactor GCG1500LBB User Manual
Gigabyte Network Card GV N52128D User Manual
Global Upholstery Co Indoor Furnishings Intensive Use and Multiple Shift User Manual