125
T
tan
Please read these instructions before use.
Lire ces instructions avant utilisation.
Lea estas instrucciones antes del usarlo.
E
F
S
LAMINATOR CONTROLS
I
A
J
B
C
T
itan
K
H
D
E
F
G
L
QUICK START GUIDE
SETTING UP THE LAMINATOR
1
2
3
4
STEPS TO LAMINATE
5
6
7
8
9
10
11
12
3
E
ENGLISH
CAPABILITIES
Performance
Technical Data
Entry width
Estimated heat-up time
Cool down time
Lamination speed
Laminating mechanism
Ready indication
Easy-Access open mechanism
HeatGuard™ technology
Clear Path
12.5” / 317mm
4 minutes
30-60 minutes
Voltage / Frequency /
Current(Amps)
Wattage
120V AC, 60Hz, 8.5A
1100 Watts
Dimensions (WxDxH)
variable - max. 35” / 90cm/min
Belt-drive
25” x 8.5” x 6.3” / 634 x 215 x 159mm
22lb / 10 kg
Net weight
Light & beep
Laminating capacity (max thickness)
Max pouch thickness
0.04”
10 Mil. / 250 micron
Yes
Yes
(total thickness = 2 x 10 = 20 Mil.)
Yes
Yes (30 mins)
Yes
Auto shut-off
Photo-capable
Carrier-free
Yes
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
Please read before use and keep for future reference.
When laminating:
- plug the machine into an easily accessible main socket.
- to prevent electrical shock - do not use the appliance close to water, do not spill water on to the appliance, power cord or main
socket.
- when working with very small pouch sizes (less than 3” / 75mm long) place the pouch within a carrier or on a sheet of paper.
DO ensure the machine is on a stable surface.
DO NOT use appliance if the power cord is damaged.
DO test laminate scrap sheets before final laminations.
DO remove staples and other metal articles prior to laminating.
DO keep the machine away from heat and water sources.
DO turn off the machine after each use.
DO unplug the machine when not in use for an extended
period.
DO NOT attempt to open or otherwise repair the machine
beyond the Easy-Access functions.
DO NOT exceed the machines quoted performance.
DO NOT allow children to use this machine without adult
supervision.
DO NOT laminate sharp or metal objects (eg: staples, paper
clips).
DO NOT laminate heat-sensitive documents (eg: tickets,
ultrasounds etc).
DO use pouches designed for use at the appropriate settings.
DO keep away from pets, while in use.
DO only use Fellowes Roller Wipes (CRC #57037) for internal
cleaning.
DO NOT laminate with self-adhesive pouches (which require a
cold setting).
DO NOT laminate an empty pouch.
DO NOT use sharp objects to clean laminator.
4
LAMINATOR CONTROLS
A
B
C
Easy-Access opening cover
Adjustable document entry guide
Entry support shelf
G
H
I
Selection buttons (up/down/left/right)
Select / OK button
Detachable document exit tray
On/off switch (at rear)
D
Reverse button
J
E
F
Standby button
K
L
Carry points (at sides)
Ready LED
LED user interface
FEATURES & TIPS
TitanTM operates at a fixed temperature. The user only needs to select the required pouch setting before laminating. There is no
need to wait for the machine to warm-up or cool-down when switching between thick or thin pouch settings. Once the laminator
has reached normal operating temperature, simply select the pouch thickness required and laminate immediately.
FEATURES
TIPS
Always put item into the appropriate sized pouch.
Always test laminate with a similar size and thickness
before final process.
If required, trim excess material from around the item
after lamination and cooling.
For best results, use Fellowes® brand laminating pouches:
Enhance 3 Mil, Capture 5 Mil, Protect 7 Mil, Preserve 10
Mil.
‘Hot Swap’ function.
•
•
The Hot Swap function enables the user to
instantly switch between thick and thin pouch
settings without any processing delays.
•
•
Easy-Access open mechanism
The Easy-Access mechanism allows user to safely
and easily open the laminator for cleaning and
maintenance.
•
•
•
When working with different pouch thickness’ (tempera-
ture settings) it is recommended to start first with the
thinnest pouches.
Prepare pouch and item for lamination. Center item in
pouch against the leading sealed edge. Ensure the pouch is
not too large for the item.
HeatGuard™ technology
Keeps the laminator surface up to 50% cooler
and makes it more energy efficient then compa-
rable laminators.
SAFE TO TOUCH
‘Safe Start’ function
Please read these instructions before use.
When switched on, the machine has a default
‘Safe Start’ function which is set to the 3 Mil.
setting. You may select other thickness settings
as required.
Power Save
The Auto shut-down switches the machine off if it
hasn’t been used for 30 mins to save energy.
To return to the “Home” Menu at any stage, press
the “Left/back” key on the navigation buttons.
5
SETTING UP THE LAMINATOR
1. Place the machine on a stable surface. Ensure enough
clear space behind the machine to allow items to pass
through freely.
3. Plug the machine into an easily accessible main socket.
4. To fully support pouches and items of different sizes
use the adjustable entry guide to center the item
before laminating. Place exit tray onto the rear of the
machine.
Connect the supplied power cord to the machine.
2.
STEPS TO LAMINATE
5. Switch the power on (Power switch located at the rear
9. Place item into open pouch. Center the item against
the sealed front edge. Use the appropriate pouch size
for the item.
of the machine).
6. Select the ‘Standby’ button on the control panel. The
3 Mil. and ready LED’s will flash for 5 seconds before
automatically selecting the 3 Mil. heat setting. Any
setting can be selected at any time as required. Allow
the machine to cool before opening.
Place the pouch, sealed edge first into the document
10.
entry. Keep the pouch straight and centered within the
document entry, not on an angle. Use the entry mark-
ings as a guide.
The LED interface allows selection of these functions:
- 3, 4, 5, 7, 10 Mil. pouch settings
- Manual laminating
Upon exit, the laminated pouch is hot and soft. Take
11.
care and remove the pouch immediately. Place the
pouch onto a flat surface to cool. This helps prevent any
jamming.
- Reverse
- ‘Easy-Access’ for cleaning and maintenance.
7.
The laminator will automatically select the thinnest
To reverse the laminating process at any stage, press
12.
pouch setting (3 Mil.) within 5 seconds of power-on
unless another setting is selected. During warm-up or
cool-down, the selected pouch setting will flash red.
and hold the ‘Reverse’ button to eject the item. The
laminator will sound alerts continuously and the ready
LED will flash.
When the laminator has reached the chosen setting, the
LED will stop flashing and glow red. The machine will
sound 2 short alerts.
8.
NEED HELP?
Let our experts help you with a solution.
Customer Service:
Always call Fellowes before contacting your place of purchase.
See back cover for useful telephone numbers.
6
MAINTENANCE - Easy-Access™
The TitanTM laminator can be opened manually by selecting the ‘open’ setting ( ) on the control panel.
Please note: the power supply and the machine must both be ON to release the electronic safety catch.
Select the ‘open’ setting
The ready LED will
flash and the machine
will cool down. This
may take between
30-60 minutes.
When the machine has
cooled to a safe tempera-
ture, the ready LED will
stop flashing and an alert
will sound.
To open the top cover,
move the levers on each
side of the machine
backwards to release the
electronic safety catch.
(
) using the naviga-
tion buttons on the
control panel. Press ‘OK’
button.
Lift the top cover with
both hands. The lami-
nating engine and
belt-drive mechanism
will be visible.
To open the belt-drive
Take care when cleaning
any residue from the roll-
ers. Fellowes laminator
wipes (CRC# 57037) are
recommended.
IMPORTANT:
mechanism, Pull the 2 cam
levers forwards, on each
side of the mechanism. The
upper carriage can now
be lifted upwards from the
front. Lift the carriage and
open fully until it stops in
the rest position.
When closing the mecha-
nism, ensure the 2 cam
levers are both pushed
forwards to lock the belt-
drive carriage correctly in
position. The lid can be
closed when the carriage
is correctly locked.
ADJUSTABLE ENTRY GUIDE
The Entry Guide can be manually adjusted (especially for smaller documents) to ensure the
items are best supported when inserted and helps avoid mis-feeds.
INTEGRATED CARRY POINTS
The TitanTM laminator has integrated carry points for safe and easy movement of the laminator
– push in the flaps on both ends of the laminator to access them.
7
WORLDWIDE WARRANTY
Fellowes warrants all parts of the laminator to be free of defects in material and workmanship for 2 years from the date of
purchase by the original consumer. If any part is found to be defective during warranty period, your sole and exclusive remedy will
be repair or replacement, at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases of abuse,
mishandling or unauthorized repair. Any implied warranty, including that of merchantability or fitness for particular purpose,
is hereby limited in duration to the appropriate warranty period set forth above. In no event shall Fellowes be liable for any
consequential damages attributable to this product. This warranty gives you specific legal rights. You may have other legal rights
that vary from this warranty. The duration, terms and conditions of this warranty are valid worldwide, except where different
limitations, restrictions or conditions may be required by local law. For more details or to obtain services under this warranty,
please contact Fellowes or your dealer.
PRODUCT REGISTRATION
Thank you for purchasing a Fellowes product. Please visit www.fellowes.com/register to register your product and benefit from
product news, feedback and offers. Product details can be found listed on the rating plate positioned on the rear side or underside
of the machine.
STORAGE & EXTERNAL CLEANING
Unplug the machine at the wall. Allow the machine to cool.
The outside of the machine can be cleaned with a damp cloth. Do not use solvents or flammable materials to polish the machine.
Cleaning sheets (CRC# 53206) can be used with the machine. When the machine is warm, run the sheets through the machine to
clean any residue off the rollers.
8
TROUBLESHOOTING
Problem
Possible cause
Solution
Switch on machine at rear next to plug
inlet and at the wall socket
Move the machine to a cooler and
dry area
No ‘red’ power on LED
Machine is not switched on
Ready light does not come on after a
long period
Machine is in a hot or humid area
Item may be too thick to laminate
Thickness setting may be incorrect
Pass through the machine again
Check pouch thickness is correctly
selected and pass through again
Check pouch thickness is correctly
selected and pass through again
Pouch does not completely seal the item
Pouch has waves or bubbles
Pouch is lost in the machine
Thickness setting may be incorrect
Pouch is jammed
Select reverse button and pull out the
item by hand. Select the open machine
setting and clean the rollers.
Pouch was used ‘open end’ first
Pouch was not centered on entry
Pouch was not straight upon entry
Empty pouch was used
Jamming
Pass cleaning sheets (CRC# 53206)
through the machine to test and
clean rollers. Select the open machine
setting and clean the rollers with
Fellowes roller wipes (CRC# 57037).
Pouch is damaged after lamination
Damaged rollers or adhesive on rollers
Cannot open top cover to gain ‘Easy
Access’
Top cover locking screw is still located on the Remove the screw then open the lid
left side of the machine
as advised.
Select ‘Easy Access’ and open the
machine. Remove the pouch and
laminate small pouches with a carrier
or on a sheet of paper.
Pouch may be too small to use without a
carrier
Small pouch is lost in the machine
9
FCC CLASS B NOTICE
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CANADA CLASS B NOTICE - AVIS CANADA, CLASSE B
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
MODIFICATIONS
Any modifications made to this device that are not approved by Fellowes may void the authority granted to the user by the FCC and/or
by Industry Canada to operate this equipment.
Toutes modifications apportées à ce dispositif et non approuvées par Fellowes annuleront le droit accordé à l’utilisateur par le FCC et/
ou par Industrie Canada de faire fonctionner cet équipement.
Fellowes
Australia
Benelux
Japan
+81-(0)-3-5496-2401
+82-(0)-2-3462-2844
+60-(0)-35122-1231
+48-(22)-771-47-40
+7-(495)-228-14-03
+65-6221-3811
+61-3-8336-9700
+31-(0)-76-523-2090
+1-905-475-6320
Korea
Malaysia
Polska
Canada
Deutschland
España / Portugal
France
+49-(0)-5131-49770
+ 34 902 33 55 69
+33-(0)-1-78-64-91-00
+39-71-730041
Russia
Singapore
United Kingdom
United States
+44-(0)-1302-836836
+1-630-893-1600
Italia
404418
|