IMPORTANT NOTE!
This gauge has an hour meter and
odometer preset option available only
for the first 1.0 engine hour and 10
miles (16km). See “ODO/HR
UTV-1000
Multi Gauge for
2004-2006 Yamaha Rhino
PRESET” for instructions.
Operation menu
Left switch functions
Pressing the left switch during normal gauge operation will move through the below commonly viewed functions
for convenience.
000000
1200A
Odometer
Clock (hold left switch to set)
Setting clock:
Left switch press moves between hours and minutes
Right switch press changes current value
Hold left switch again to exit clock set mode
H 00
Hourmeter
Right switch functions
Pressing the right function switch during normal operation will scroll through the following display functions. A
heading will first appear after each press to display what display function is currently selected. After about 2
seconds, the display will show the data for the selected function.
Heading
trip A
trip b
Data
a 00
b 00
Description
Trip A (hold right switch to reset)
Trip B (hold right switch to reset)
srv mi(srv km) s 0000
Count down Service odometer if enabled (hold right switch to reset)
Count down service hour meter if enabled (hold right switch to reset)
srv hr
mph(KPH)
tach
sh 000
00 mph(00 KPH) Alternate speed display (hold right switch to change primary unit)
r 0000
Tachometer displays in information center
page 1
MAN#650231:A
6. Fuel sender installation (optional tube sender from Dakota Digital):
a. To mount the sensor you will need to drill a hole in the fuel tank. Use a 1” hole saw, and drill a hole adjacent to
the small dimple on the gas tank closest to the passenger side of the vehicle. Use a fuel safe sealant and coat
the supplied cork gasket to provide a leak free seal from the tank to the sensor. Secure the sensor with the
supplied stainless screws. DO NOT OVER TIGHTEN THE SCREWS.
b. Attach the wiring harness provided with the sender. Connect the Red wire to the POS terminal. Connect the
Black wire to the NEG terminal. Connect the GREEN wire to the SEND terminal.
c. Route the wire harness up to the gauge mounting location using supplied zip ties to tie the harness so that it will
not be pinched or damaged.
7. Locate the stator rotation detection wire (red wire,
pin 6 in the 8 pin connector coming out of CDI
module located near the battery) and place the
included T-tap connector onto it using a pair of
pliers. This wire will be used for the tachometer
signal.
8. Route the wires from the UTV gauge through the hole in the gauge opening and place gauge into opening. Secure
the gauge with the three provided washers and thumb nuts.
9. Route the yellow tach wire to the T-tap connector for the tachometer and plug into the connector.
10. Plug the four pin connector from the oil pressure harness into the four pin connector in back of gauge.
11. If using a separate fuel sender plug the three pin connector from the fuel sender harness into the three pin connector
in the back of the gauge.
12. Locate the three gauge connectors in the Rhino harness. These connectors will be located close to the gauge mount
location on the under hood side of the dash panel.
13. Plug the 6 pin gauge connector into the 6 pin connector on the Rhino.
14. Plug the 4 pin gauge connector into the 4 pin connector on the Rhino
15. Plug the 3 pin gauge connector into the 3 pin connector on the Rhino.
16. Reconnect battery.
17. Turn the key on and verify that the gauge functions as expected.
18. Start engine and check for oil and water leaks. Shut off engine.
19. If there are no oil or water leaks, reinstall the floor panels, engine covers and seats as described in the service
manual.
20. Installation is now complete. If you experience difficulties check the troubleshooting section in this manual.
SETUP
To enter the setup menu, press and hold the left switch while turning the key on. If your speed calibration differs from
stock due to non-stock tires or gears and you will be calibrating the speedometer, press and hold the left switch while
starting the engine.
-Press the left switch to move through the menus or change the settings after a menu option is selected.
-Hold the left switch for more than 2 seconds to scroll through options or settings
-Press the right switch to select a menu option or to save a setting and go back to the menu.
SETUP
INFO
Release switch to enter setup menu
Information menu
VER
Displays software version
Current software version
Displays current speed cal value
Current speed cal value
Returns to info menu
U113
SP CAL
160000
MAIN
SPEED
Speed gauge menu
UNIT
Select unit for speed
Toggle between MPH and KPH (select unit to use for calibration)
Auto calibrate speed to a marked mile or kilometer
AUTO
page 3
MAN#650231:A
Pulls up all values on speed and speed pulses in odometer
Press Right switch to finish cal and save value
ADJUST
ADJUST
SRV MI (SRV KM)
OFF ( OFF)
500 ( 800)
….
Adjust speed cal while driving
Each press of left switch toggles direction of adjustment, right switch to save and exit
Sets value of service odometer set when service odometer is reset
Turns off the count down service odometer (default)
Sets service to 500 mi or 800 km when resetting service odometer.
Service point can be set in 500 mi (800km) increments.
Sets service to 7500 mi or 12000 km when resetting service odometer.
Returns to info menu
7500 (12000)
MAIN
TACH
Tachometer gauge menu
ENGINE
WARN
Sets number of cylinders from 1-15 (default 12 for use on alternator output)
Sets RPM warning point (default 5500 RPM)
Minimum warning point of 2250 RPM
W 2250
….
W 9750
Warning point can be set in 250 RPM increments
Maximum warning point of 9750 RPM
SRV HR
Sets service hour value used when resetting count down service hour meter
Service hour meter disabled (default)
OFF
10
Minimum service hour set point
…
310
Service hour reset point can be set in 10 hr increments
Maximum service hour set point
MAIN
Returns to info menu
GAUGES
Gauge option menu
VLT HI
VLT LO
FL SND
Set high voltage warning point (default 15.4V)
Set low voltage warning point (default 11.1 V)
Set fuel sender used
NONE
STOCK
No fuel sender used, fuel area will be blanked out (default)
Uses stock fuel sender for Rhino
DAKDIG
CUSTOM
Uses Dakota Digital sender to be installed in tank
Uses custom sender, user must calibrate for the sender curve
CAL Y (CAL N)
EMPTY
ADD 33
ADD 66
ADD 99
DONE
Select CAL Yto calibrate sender
Start with empty tank, or fuel sender in empty position
Fill fuel to 1/3 tank, press right switch to save point
Fill fuel to 2/3 tank, press right switch to save point
Fill fuel to full tank, press right switch to save point
Custom fuel calibration is complete, press right switch to go back to menu
Set low oil pressure warning point (default 9 PSI)
Set high water temp warning point and set temperature unit (default 230F)
Select temp unit, press left switch to change, right switch to save
Select high warning, left switch to change, right switch to save
Returns to info menu
OIL LO
WTR HI
DEG F (DEG C)
WTR HI
MAIN
OPTION
Option menu
DIM LV
OFF
Adjust dimming point on gauge
Dimming function is off
LVL 1
…
Gauge will dim when light on gauge face is very low (default)
7 selectable dimming levels
LVL 7
DM OUT
Gauge will dim early when more light is on gauge face
Enables/disables dim output for other gauges
Dim output will be high when gauge is dimming
Dim output will be disabled (default)
ON
OFF
WN OUT
Selects which gauges provide a warn out signal on warn out wire (default all on)
Gauges that provide signal out are lit up, left switch to change, right switch to save
Warn output wire is disabled
WN OUT
NO WRN
page 4
MAN#650231:A
CLOCK±
-7 SEC
Adjust clock speed for accuracy
Subtract 7 seconds from clock every 24 hrs
…
0 SEC
No adjustment to factory clock speed (default)
…
+7 SEC
Add seven seconds to clock every 24 hrs
St odo
Set hr
MAIN
Allows presetting of odometer value on initial install (not available after 10 miles / 16km)
Allows presetting of hour meter value on initial install (not available after 1.0 hrs)
Returns to info menu
DONE
Leaves setup menu if selected
ADDITIONAL SETUP NOTES:
SPEED – AUTO
This setup option allows calibrating to a known mile or kilometer. By default, the speed is calibrated to use the Rhino
Factory speed signal. Calibration should only be needed if the factory calibration is no longer correct due to changes to
tires or gearing.
1. Start with vehicle at the beginning of the marked mile or kilometer and turn the key off.
2. Start engine while holding the left switch to enter setup.
3. Select speed option in setup and select appropriate unit (if you will be calculating to a known kilometer choose KPH,
else choose MPH).
4. Select the Auto option. The gauge will light all the displays and the speed display will read
5. Begin driving the mile or kilometer. The message center will read the number of pulses read from the speed signal.
This value cannot be used to determine if a mile or kilometer has been driven.
6. At the end of the mile or kilometer, stop the vehicle and press the right switch to save the new speed calibration. The
gauge will return to the speed setup menu.
SPEED – ADJUST
This setup option allows adjustment to speed while driving. By default, the speed is calibrated to use the Rhino Factory
speed signal. Calibration should only be needed if the factory calibration is no longer correct due to changes to tires or
gearing.
1. Start vehicle while holding the left switch to enter setup.
2. Select speed option in setup and select appropriate unit (if you will be calculating to a known kilometer choose KPH,
else choose MPH).
3. Select the ADJUST option. The gauge will light all the displays and the message center will read ADJUST
4. Follow another vehicle traveling at a constant known speed. Hold the left switch to begin increasing the speed
reading. To decrease the speed reading, release the switch and press and hold the switch again.
5. The direction of adjustment will change each time the switch is released.
6. When the speed has been adjusted, press the right switch to save the new speed calibration. The gauge will return
to the speed setup menu.
SERVICE METERS
This gauge has two service meters. These are a countdown hour meter and a countdown odometer. Both service meters
can be disabled, or enabled independently. This allows for setting of two individual service points, one based on engine
run time, the other based on odometer. This could also allow for setting a service point on whichever service point comes
first, hourly or odometer.
When the setup point is reached, SERVICE DUEwill scroll in the message center. Pressing either switch will clear the
message until the next time the key is turned on. Once the service has been done, use the left switch to select the service
meter that is due (display will show a negative value or zero). Press and hold the right switch to reset the service meter to
the value set in setup.
The service meter can be disabled by selecting in setup. If a new value is set for the service meter, and the meter was
previously set to OFF, the service message may immediately be displayed. Reset the service meter to begin a new
countdown.
page 5
MAN#650231:A
ODO/HR PRESET
Within the first 10 miles (16 km) and 1.0 engine hours after first installing the gauge, the option is available for a ONE
TIME preset of the odometer and hour meter to the reading(s) of the previous gauge. If this option is not used within the
first 10 miles (16 km) or 1.0 engine hours or an incorrect reading is saved, the gauge will need to be returned to Dakota
Digital for any odometer/hour meter adjustment. The procedure to preset the meters is as follows:
1. If setting odometer select st odo option in setup. If setting hour meter select set hr.
2. For odometer preset, verify that correct unit is displayed above message center. If not, turn key off to leave setup
and use unit option under speed to set correct unit. NOTE: Preset MUST be done with correct unit or odometer
will not be set correctly!
3. The current odometer / hour meter value is displayed with the first digit blinking
4. Press and release the left switch to change the digit. Press and release the right switch to move on to the next digit.
5. Repeat step 4 until all digits are set. After tenths digit is set, press and release the right switch.
6. Water temp display will read “”. Check the current unit (if in odo preset) and the odometer / hour meter value to
make sure it is correct. If not, press and release the right switch to go back and make changes.
7. NOTE: Check the displayed odometer value VERY carefully before next step. After selecting yes, you will no
longer be able to change the odometer / hour meter.
8. If the settings are all correct, press and release the left switch. Water temp display will read “”.
9. Press and release the right switch to preset the odometer / hour meter to the new value.
SELECTING FUEL SENDER
By default, no fuel sender is selected and the fuel display will be blank. If a fuel sender is used a fuel sender must be
selected. Use the fuel sender option in the Gauges menu to select used fuel sender. The name of the fuel sender is
displayed in the message center. Two numbers are also displayed on the right side of the panel. The upper number is the
sender resistance in ohms at full tank. The lower number is the sender resistance in ohms at empty tank.
CUSTOM FUEL SENDER SETUP
If a fuel sender other than the Rhino stock fuel sender or the Dakota Digital fuel sender is used, the gauge needs to be
calibrated to the new fuel sender. The custom fuel sender option in the gauges menu allows this function.
1. Begin with an empty (or near empty) fuel tank.
2. Select custom fuel sender option in gauge setup menu.
3. Use left switch to change to change to CAL Yand then press the right switch to select.
4. The gauge will light two numbers on the right side. The lower number is the current resistance of the fuel sender in
ohms. The upper number is the tank percentage point currently being calibrated.
5. Four points are needed to calibrate the sender, empty, 33%, 66%, 99% (full tank). The gauge expects calibration to
start at empty and move to each of these points.
6. Gauge will display EMPTY. Make sure tank is empty or sender is at empty point. Press the right switch to save point
in calibration.
7. Gauge will display ADD 33. Add fuel to 1/3 tank or move sender to 1/3 full point. Press the right switch to save point
in calibration.
8. Gauge will display ADD 66. Add fuel to 2/3 tank or move sender to 2/3 full point. Press the right switch to save point
in calibration.
9. Gauge will display ADD 99. Add fuel to full or move sender to full point. Press the right switch to save point in
calibration.
10.Gauge will display DONE. Press the right switch to finish calibration and return to gauges setup menu.
OPTION – DIM OUT
The dim out option allows the dim output to be turned on or off. The dim output is used if you have installed other Dakota
Digital gauges and would like this gauge to also control the dimming of these gauges. If the dim out option is turned on,
12v is sent out on the dim out wire when the gauge is dimming. In this mode, the gauge will be either in dim mode or full
brightness mode.
If no other gauges are to be dimmed, this option can be set to off. In this mode the gauge will fade when dimming and
gauge dimming will be less noticeable.
page 6
MAN#650231:A
TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
Gauge does not light up
Gauge has bad ground or power
Check connections to wiring harness and check
wiring harness and gauge wires for pinched or
broken wires.
Tach always stays blank
Tach wire is not connected properly
Engine value set incorrectly
Engine value set incorrectly
Speedometer needs to be recalibrated See setup for speed calibration instructions.
Dim level is set to off or set too low
Check for good connection to alternator wire.
Set Engine value to 12 for alternator (see setup)
Set Engine value to 12 for alternator connection
Tach reads incorrectly
Speed reads incorrectly
Gauge does not dim
Gauge is always dim
Set dim level to higher level (see setup)
Set dim level to lower level (see setup)
Dim level is set too high
Light sensor over left switch is covered Make sure left side of lens is not covered.
RANGEdisplayed during
custom fuel setup
ADD FUELis scrolled
during custom fuel setup
SND HIdisplayed during
custom setup
Fuel sender resistance is too high
Check for good connection to fuel sender and fuel
sender to ground. Sender must be below 1000Ω
Add fuel until next third of tank or move sender to
the next third tank position.
Fuel sender was started with falling resistance and
now the resistance has risen. Correct fuel position
or start custom programming over by turning off
key.
Resistance has not changed enough
since previous point.
Fuel sender resistance is higher than
expected.
SND LOdisplayed during
custom setup
Fuel sender resistance is lower than
expected.
Fuel sender was started with rising resistance and
now the resistance has fallen. Correct fuel position
or start custom programming over by turning off
key.
PROBLEM
is displayed in fuel, oil,
or water display
CAUSE
No sender connected, or incorrect
sender selected.
SOLUTION
Check proper connection to sender. Check for
broken or pinched sensor wires.
For water temp sender, check for good ground
and remove any sealant tape on threads of
sender.
If no fuel sender is being used, set the fuel sender
option to off in setup. This will blank out the fuel
display.
Sensor wire is shorted to ground.
Check sensor wire harness for correct connection
to sensor. Check for pinched or broken sensor
wire harness.
is displayed in fuel, oil
or water display.
SERVICE DUEis scrolled
in the message center
One of the countdown service meters
has reached zero
Perform service and reset service meter by
holding right switch when service meter is
displayed. If service meter operation is not
desired, disable service meter by setting to in
the setup menu.
page 7
MAN#650231:A
SERVICE AND REPAIR
DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical consultation is available to help you work through any questions or
problems you may be having installing one of our products. Please read through the Troubleshooting Guide. There, you will find the solution to most problems.
Should you ever need to send the unit back for repairs, please call our technical support line, (605) 332-6513, to request a Return Merchandise Authorization
number. Package the product in a good quality box along with plenty of packing material. Ship the product by UPS or insured Parcel Post. Be sure to include the RMA
number on the package, and include a complete description of the problem with RMA number, your full name and address (street address preferred), and a telephone number
where you can be reached during the day. Any returns for warranty work must include a copy of the dated sales receipt from your place of purchase. Send no money. We will
bill you after repair.
Dakota Digital 24 Month Warranty
DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it, under normal use and condition, be proven defective in material or
workmanship within 24 MONTHS FROM THE DATE OF PURCHASE, such defect(s) will be repaired or replaced at Dakota Digital’s option.
This warranty does not cover nor extend to damage to the vehicle’s systems, and does not cover removal or reinstallation of the product. This Warranty does not
apply to any product or part thereof which in the opinion of the Company has been damaged through alteration, improper installation, mishandling, misuse, neglect, or
accident.
This Warranty is in lieu of all other expressed warranties or liabilities. Any implied warranties, including any implied warranty of merchantability, shall be limited to
the duration of this written warranty. Any action for breach of any warranty hereunder, including any implied warranty of merchantability, must be brought within a period of 24
months from date of original purchase. No person or representative is authorized to assume, for Dakota Digital, any liability other than expressed herein in connection with
the sale of this product.
4510 W. 61ST St. N., Sioux Falls, SD 57107
Phone: (605) 332-6513 FAX: (605) 339-4106
©Copyright 2009 Dakota Digital Inc.
page 8
MAN#650231:A
|